WESTERN® IMPACT™ UTV snow plows are professional-grade plows ideal for homeowners, residential properties, municipalities, parks, schools, hospitals and government buildings in Huber Heights. Designed and built exclusively for utility vehicles these plows are great for snow removal on sidewalks, driveways and pathways. The 6' wide v-plow easily adapts to handle 5' sidewalks and gates in angle, scoop or V mode. The 6' straight blade is a commercial grade snow plow in a lightweight package that fits more UTVs.
Hooking up the IMPACT™ v-plow or straight blade is simple. With the receiver brackets installed on your utility vehicle, either drive onto or manually push the plow into the receivers. Push up on the headgear to engage the hitch pins in the receiver holes, then slide the handle to lock the hitch pins in place. Finally, connect the electrical plug. Detaching the plow is just as easy. The receivers are removable, to maintain ground clearance.
The removable receivers and low profile undercarriage provide exceptional ground clearance and maximize the ramp angle, so your unit will be trail ready when the plow is not attached.
We manufacture our own hydraulic components to ensure the highest standards of quality and reliability, so that you get a hydraulics system that's not only fast and responsive, but that's built to last season after season. Fully enclosed components are protected from the elements. Hydraulic Scrape Lock holds the blade down for more efficient scraping and clean back dragging.
The IMPACT™ straight blade UTV plow features a 14-gauge powder coated steel moldboard that is 6' wide and comes with a standard 5" steel cutting edge.
Four vertical ribs and high-strength, low-weight, alloy steel components ensure the plow is strong enough for commercial operation and light enough to fit more UTVs.
Two heavy-duty coil springs protect your plow and UTV by allowing the whole blade to trip when striking obstacles.
The IMPACT™ flared v-plow blades go from a 25¼" center height to a full 29¼" at the outer edge. The 14-gauge powder coated steel flared moldboard is 6' wide and comes with a standard 5" high-carbon steel cutting edge, reducing wear and extending the life of the blade.
Six vertical ribs, coupled with high-strength, low-weight, alloy steel components provide a favorable strength-to-weight ratio, keeping stress off of the UTV frame. A 3/4" diameter, steel center pin resides within a three-connection-point hinge, keeping the wings tight for improved performance.
Each blade features independent trip-edge design with heavy-duty coil springs for protection when encountering bumps and obstacles. Whether in V, scoop or straight blade configuration, the trip-edge helps protect the plow, the truck and the operator. Since only the edge trips, snow remains in front of the blade, so you can keep going without spilling the entire load of snow.
A standard feature on the IMPACT™ UTV v-plow, UltraLock double-acting cylinders allow the operator to use the v-plow in straight blade mode by locking the wings together instead of having to toggle each wing independently. The double-acting cylinders also hold the wings firmly in place for clean, efficient back dragging.
For the cleanest pass in any position, the IMPACT™ UTV v-plow has a snow control deflector over the center hinge to help prevent snow from being lost over the top.
When fully angled or in V mode, the IMPACT™ UTV v-plow plowing path is 5' wide, and 4' 7" in scoop. For UTVs with a wider wheel base, a width-adjustment setting is available to make your plowing path wider in these positions. Using the alternate setting, the plowing width is 5' 6" when fully angled or in V, and 5' 1" in scoop.
The intuitive UTV-specific hand-held control lets you raise and lower the plow, and position the blade in V, scoop, angle and straight modes. An optional joystick control is also available for easy blade control operation when wearing gloves.
The ULTRAFINISH™ baked on powder coat with epoxy primer is standard on all WESTERN® plows, providing outstanding protection against wear and rust.
The WESTERN® Scrape Lock system locks the plow in any position you put it in to give you a cleaner scrape, especially while back dragging. With the plow locked in place, Scrape Lock gives you the performance of a larger plow without the extra weight and without the need to push any extra buttons.
The exclusive WESTERN® SECURITY GUARD™ snowplow anti-theft system is a safe and secure way to electronically lock your snow plow when it is detached from your truck as a deterrent from theft.
The blade is pre-punched for easy installation of accessories, providing a custom fit. The pre-punched holes also prevent damage to the powder coat that can sometimes occur when installing an accessory.
|Blade Width||6' 1.83 m||6' 1.83 m|
29 ¼" at end
25 ¾" at hinge 74.29 cm at end
65.40 cm at hinge
|23 ½" 59.7 cm|
|Blade Gauge||14 1.90 mm||14 1.90 mm|
|Trip Springs||2 2||2 2|
|Vertical Ribs||6 6||4 4|
|Lift Cylinder||1½" x 6" 3.81 cm x 15.24 cm||1 ½" x 6" 3.81 cm x 15.24 cm|
|Angling Rams||1" x 8 ¾" 2.54 cm x 22.23 cm||1" x 7" 2.5 cm x 18 cm|
|Plowing Width (full angle)||
5' 0" full angle
4' 7" scoop
5' 0" full V 1.52 m full angle
1.39 m scoop
1.52 full V
|5' 4" full angle 1.6 m full angle|
|Approx. Weight (less mount)||354 lb (plus vehicle mount) 160 kg (plus vehicle mount)||261 lb (plus vehicle mount) 119 kg (plus vehicle mount)|
|Cutting Edge||¼" x 5" 0.64 cm x 12.70 cm||¼" x 5" 0.64 cm x 12.70 cm|
|Mount Type||UTV Mounting System UTV Mounting System||UTV Mounting System UTV Mounting System|